Apron Feeders use a series of overlapping metal plates to catch and move bulk materials that fall from hoppers and chutes. KMK use VVVF drives to accurately meter out material at a specific rate and a fine material conveyor sitting under the main conveyor to catch fine material which is then emptied into the feeder head chute. KMK design feeders and conveying systems to fit their location, and the required throughput of each customer.

KMK Apron Feeder

General Benefits of Apron Feeders

• ਮਜਬੂਤ
• Handle Any Bulk Material
• High Throughput Capacity
• Highly Controllable
• ਪ੍ਰਭਾਵ ਸਬੂਤ

KMK Apron Feeders

• Specifically For
  

  KMK Apron Feeder

   Each Customers Requirements

• Modular Drive And Tension Sections
• Modular Intermediate Sections For Better Installation
• Wide Range Of Belt Widths And Trough Combinations
• Designed to fit in a small envelope with low headroom
• Bed Depth Control Using Slide Gate
• Minimised Spillage And Dust Due To Full Skirting
• Integrated Fines Belt
• Belt Cleaning System
• Driven By A Shaft Mounted Variable Speed Drive

Belt Feeders use a rubber conveyor belt and an impact section with many idlers to transport materials that fall from hoppers and chutes.  KMK use VVVF drives to accurately control the speed of the conveyor and specific idler configurations for the actual load from your material.  KMK design feeders and conveying systems to fit their location, and the required throughput of each customer.

KMK Belt Feeder

General Benefits of Belt Feeders

• Best for Less Abrasive Material
• Best for Smaller Lump Sizes
• High Throughput Capacity
• Highly Controllable
• Better Impact Capacity Than Standard Conveyors

KMK Belt Feeders

KMK BELT FEEDERS

• Specifically For Each Customer Requirements
• Modular Drive And Tension Sections
• Modular Intermediate Sections For Better Installation
• Wide Range Of Belt Widths And Trough Combinations
• Bed Depth Control Using Slide Gate
• Minimised Spillage And Dust Due To Full Skirting
• Belt Cleaning System
• Driven By A Shaft Mounted Variable Speed Drive

Belt Conveyors use a rubber conveyor belt to transport materials from place to place.  Normally the material will be metered onto the belt with a feeder or a chute.  KMK use VVVF drives to accurately control the speed of the conveyor and specific idler configurations for the actual load from your material.  KMK design conveying systems to fit their location, and the required throughput of each customer.

General Benefits of Belt Conveyors

• For Any Bulk Material
• High Throughput Capacity
• Highly Controllable

KMK Belt Conveyors

• Specifically For Each Customer Requirements
• Modular Drive And Tension Sections
• Modular Intermediate Sections For Better Installation
• Wide Range Of Belt Widths And Trough Combinations
• Belt Cleaning System
• Driven By A Shaft Mounted Variable Speed Drive

Hoppers are used as buffer storage to transfer material from one system to another, for example, from a Wagon Tippler to a conveyor system.  KMK design and supply hoppers to suit any material, with the use of stainless steel and Hardox or Tivar liners as needed.  Hoppers can be fitted with Grizzley screens, rail mounted Crushers, and flip-flap gates.  Internal baffles can be used to reduce impact on equipment below the hopper.

• Specifically For Each Customer Requirements
• Sized to fit into the surrounding system
• For any material, with Hardox or Tivar Liners
• Use with Crushers or Flip Flap Dust Gates
• Design supported with DEM

• Dust suppression – e.g. Water Sprays

Dust Suppression is used to stop dust causing a problem and entering the air.  Traditionally, water is sprayed either onto the material, as the material passes, or as a screen.  This will basically coat the dust in water droplets to make them heavier.  Modern improvements include specific water nozzles that can produce a range of sprays, suited to the dust and can be linked to site operations or atmospheric conditions.

• Dust Extraction – machine specific or building wide

Dust extraction is used to remove airborne dust using a filter.  Air vents are positioned at passive or active points in the site.  A fan sucks air though the vents, pipes, and through an air filter that collects the dust.  Once the dust has been collected it can be fed back into the system.

• Tippler Cowls – Sealing the area around the Tippler

A Tippler cowl is an enclosure around the Tippler that is used to keep dust from spreading.  The cowl is made from thin-walled corrosion resistant materials.  In some areas, wear plates are used to prolong life.  The Cowl is sealed against the rotating tippler, and further seals around the wagon move into place when the Tippler rotates.  A dust extraction system is added to ensure that airborne dust is sucked in and cannot escape.

• Conveyor Cowls – Sealing the conveyor system

Conveyor Cowls are used to protect the material on a conveyor.  The material is shielded from wind and rain.  Material moving onto this conveyor can still create dust, so dust extraction is used in the cowl.

• Dust Gates – To prevent dust updraft

When material is dumped into a chute or a hopper, the impact will release dust, and the movement will cause a gust of air.  To stop the movement of the air back out of the hopper, Dust Gates can be placed at the entrance.  They are one way gates and allow material to pass through while they restrict any updraft.